First step is to download the image from Cisco.com
For the Nexus 9000 software download the latest images can be found here
Select the specific for your switch and download – (you will require a service contract)
Second step is to connect the management interface (or any L3 interface on your switch) to a network where you can see your TFTP server
In my case I have connected my laptop directly to the management port
Next ensure you have a route to your TFTP server
I will ping my laptop from the Nexus switch – both my laptop and management interface are addressed in the same /24 subnet
NEX-9K-1# ping 10.10.10.100 vrf management PING 10.10.10.100 (10.10.10.100): 56 data bytes 64 bytes from 10.10.10.100: icmp_seq=1 ttl=127 time=0.697 ms 64 bytes from 10.10.10.100: icmp_seq=1 ttl=127 time=0.697 ms 64 bytes from 10.10.10.100: icmp_seq=1 ttl=127 time=0.697 ms --- 10.10.10.100 ping statistics --- 5 packets transmitted, 4 packets received, 20.00% packet loss
Great so I can see my laptop from the switch, next step is to copy the image
Third step is to copy the image onto the switch so I need to start my TFTP server on my laptop, I am using TFTPD64
Verify you have enough space on the drive (for a new 9000 switch out the box you will have, but if this switch has been in production for a while there may be other redundant images on there.)
NEX-9K-1# dir bootflash: 4096 Jul 21 04:59:39 2017 .rpmstore/ 6175 Jul 21 05:08:30 2017 20170721_050830_poap_8529_init.log 6408 Feb 05 11:10:34 2018 20180205_110650_poap_8266_init.log 4096 Jul 21 05:01:03 2017 home/ 336 Jul 21 05:02:22 2017 license_FDO21252F67_20.lic 16384 Jul 21 04:59:34 2017 lost+found/ 555603456 Jul 21 05:01:00 2017 nxos.7.0.3.I2.5.bin 4096 Jul 21 05:05:43 2017 scripts/ 4096 Jul 21 05:05:18 2017 virtual-instance/ Usage for bootflash://sup-local 806494208 bytes used 51098030080 bytes free 51904524288 bytes total
You can see at the bottom I have 51098030080 bytes free on this switch – which is 50Gb which is plenty, the image I am upgrading to is 670Mb
To copy the image to the switch ensure your image is in your TFTP directory and start your TFTPD server and issue the following commands on the switch
NEX-9K-1# copy tftp: bootflash: Enter source filename: nxos.7.0.3.I4.7.bin Enter vrf (If no input, current vrf 'default' is considered): management Enter hostname for the tftp server: 10.10.10.100 Trying to connect to tftp server...... Connection to Server Established. Connection to Server Established. [##################..................233Mb]
This process will take a few minutes as the image is copied to the switch
Next step is to install the image – Skip to Performing the Software Upgrade
Cisco Nexus 9000 USB software upgrade
The other more convenient option is to use a USB stick and copy the software to the stick, insert the stick into the Nexus 9000 switch and initiate the copy from USB to Bootflash as below:
Once you insert your USB stick into the USB port on the front of the switch, you should see a message something like this
NEX-9K-2# 2018 Feb 5 13:30:39 NEX-9K-2%$ VDC-1 %$ %USER-2-SYSTEM_MSG: <<%USBHSD-2-USB_SWAP>> USB insertion or removal detected - usbhsd 2018 Feb 5 13:30:39 NEX-9K-2 %$ VDC-1 %$ %USER-2-SYSTEM_MSG: <<%USBHSD-2-MOUNT>> USB2: online - usbhsd
In this case the device has been assigned USB2: so this is the device we need to copy from
NEX-9K-2# copy usb2: bootflash: Enter source filename: nxos.7.0.3.I4.7.bin Copy progress 100% 702663KB Copy complete, now saving to disk (please wait)... NEX-9K-2#
This process is lot quicker, this copy took less than 20 seconds
Now you have the image on the switch we need to verify it’s there
NEX-9K-2# dir bootflash: 4096 Jul 21 05:37:55 2017 .rpmstore/ 6324 Feb 05 10:39:14 2018 20180205_103907_poap_8257_init.log 4096 Jul 21 05:39:21 2017 home/ 336 Jul 21 05:41:38 2017 license_FDO21252F7A_21.lic 16384 Jul 21 05:37:50 2017 lost+found/ 555603456 Jul 21 05:39:16 2017 nxos.7.0.3.I2.5.bin 702663680 Feb 05 12:29:50 2018 nxos.7.0.3.I4.7.bin 4096 Jul 21 05:45:02 2017 scripts/ 4096 Jul 21 05:44:37 2017 virtual-instance/
Performing the software upgrade
At this point it is recommended to perform an impact test on the software install, this is a series of test scripts that the switch will run through to check the impact of installing this software image
It is not a requirement for the software upgrade but just a good sense check to make sure all is ok.
NEX-9K-2# show install all impact nxos nxos.7.0.3.I4.7.bin Installer will perform impact only check. Please wait. Installer is forced disruptive Verifying image bootflash:/nxos.7.0.3.I4.7.bin for boot variable "nxos". [####################] 100% -- SUCCESS Verifying image type. [####################] 100% -- SUCCESS Preparing "nxos" version info using image bootflash:/nxos.7.0.3.I4.7.bin. [####################] 100% -- SUCCESS Preparing "bios" version info using image bootflash:/nxos.7.0.3.I4.7.bin. [####################] 100% -- SUCCESS12MBHW 200.68MB Performing module support checks. [####################] 100% -- SUCCESS Notifying services about system upgrade. [####################] 100% -- SUCCESS Compatibility check is done: Module bootable Impact Install-type Reason ------ -------- -------------- ------------ ------ 1 yes disruptive reset Incompatible image for ISSU Images will be upgraded according to following table: Module Image Running-Version(pri:alt) New-Version Upg-Required ------ ---------- ---------------------------------------- -------------------- ------------ 1 nxos 7.0(3)I2(5) 7.0(3)I4(7) yes 1 bios v07.59(08/26/2016):v07.59(08/26/2016) v07.51(02/15/2016) no
All tests have passed with SUCCESS so let’s perform the upgrade – this will perform the same checks but at the end actually perform the install.
Issue the command install all nxos bootflash:nxos.7.0.3.I4.7.bin
NEX-9K-1# install all nxos bootflash:nxos.7.0.3.I4.7.bin Installer will perform compatibility check first. Please wait. Installer is forced disruptive Verifying image bootflash:/nxos.7.0.3.I4.7.bin for boot variable "nxos". [####################] 100% -- SUCCESS Verifying image type. [####################] 100% -- SUCCESS Preparing "nxos" version info using image bootflash:/nxos.7.0.3.I4.7.bin. [####################] 100% -- SUCCESS Preparing "bios" version info using image bootflash:/nxos.7.0.3.I4.7.bin. [####################] 100% -- SUCCESS Performing module support checks. [####################] 100% -- SUCCESS Notifying services about system upgrade. [####################] 100% -- SUCCESS Compatibility check is done: Module bootable Impact Install-type Reason ------ -------- -------------- ------------ ------ 1 yes disruptive reset Incompatible image for ISSU Images will be upgraded according to following table: Module Image Running-Version(pri:alt) New-Version Upg-Required ------ ---------- ---------------------------------------- -------------------- ------------ 1 nxos 7.0(3)I2(5) 7.0(3)I4(7) yes 1 bios v07.59(08/26/2016):v07.59(08/26/2016) v07.51(02/15/2016) no Switch will be reloaded for disruptive upgrade. Do you want to continue with the installation (y/n)? [n]
Select Y to progress with the install
Install is in progress, please wait. Performing runtime checks. [####################] 100% -- SUCCESS Setting boot variables. [####################] 100% -- SUCCESS Performing configuration copy. [####################] 100% -- SUCCESS Module 1: Refreshing compact flash and upgrading bios/loader/bootrom. Warning: please do not remove or power off the module at this time. [####################] 100% -- SUCCESS Finishing the upgrade, switch will reboot in 10 seconds. NEX-9K-2# [ 722.735442] [1517836762] writing reset reason 88, 2018 Feb 5 13:19:22 NEX-9K-1 %$ VDC-1 %$ Feb 5 13:19:22 %KERN-0-SYSTEM_MSG: [ 722.735442] [1517836762] writing reset reason 88, - kernel [ ü CISCO SWITCH Ver7.59 Device detected on 0:6:0 after 0 msecs
The switch will now reload and when it’s back online, we just need to verify it is running the new image, during the reboot you can see if it is booting the new image
Trying to read config file /boot/grub/menu.lst.local from (hd1,4)
Filesystem type is ext2fs, partition type 0x83
Booting bootflash:/nxos.7.0.3.I4.7.bin ...
Booting bootflash:/nxos.7.0.3.I4.7.bin { Yes it is..!}
Trying diskboot
Filesystem type is ext2fs, partition type 0x83
Image valid
Image Signature verification was Successful.
Final verification is to log into the switch and issue the show version command
NEX-9K-2# sh ver Cisco Nexus Operating System (NX-OS) Software Software BIOS: version 07.59 NXOS: version 7.0(3)I4(7)
